Spin
A glowing spinning top closed by a flat top, on a finely fluted base.
From RM379.00
Cordless Lamps
Light, without the cord.
Five shades. One base.
Charged over USB-C.
No bulb. The light is in the base.
And Hotaru, in eight colours.
Get the highlights.
Day and night.
By day it is a printed object in the colours you chose. Switch it on, and the shade becomes the light.
Made to come apart.
Coming soon · Hotaru
Three parts and a light.
A low base holds the rechargeable light, the orb sits on it with magnets, and a flat top closes it. Each part is printed in a tone of the same colour.
16 magnets USB-C charging
8
colours
USB-C
charging
16
magnets
0
cords while it is lit
Spin
A glowing spinning top closed by a flat top, on a finely fluted base.
From RM379.00
Higasa
A parasol of light: a pleated dome over a pleated column, its 28 pleats turned through 35 degrees, on a slim rechargeable base.
From RM379.00
Tsutsu
A short drum of 32 fluted channels, turned 15 degrees as they rise, under a flat glowing top.
From RM379.00
Kasane
Three ribbed tiers, each smaller than the one below, stacked like boxes under a flat glowing top.
From RM379.00
Tsumugi
A cocoon of a column in a fine knit, swelling a little below its middle, under a flat glowing top.
From RM379.00
Cordless Lamps
A lamp that never asks where the socket is.
Printed shades on one slim rechargeable base. Carry it from the dining table to a bedside or a bathroom shelf, with nothing running under it. Indoors only.
Not on sale yet
Expected around RM379.00, complete
USB-C
Charged by cable
The base charges over USB-C, and the cable is in the box. Battery and running time go on each lamp's page once the LED module is chosen.
No bulb
The light is inside the base
An LED module sits in a well in the base, its light facing up into the shade. Nothing to plug in while it is lit.
4
Four shades, one base
Higasa, Tsutsu, Kasane and Tsumugi sit on the same 96 mm printed base, on four magnets, so a shade lifts straight off.
0.84 mm
Two walls thick
Two continuous walls of translucent PLA, no infill. Thin enough that the material itself glows rather than merely holding a shape.
Put it down anywhere.
Printed to order in Malaysia, one at a time, in a wall two beads thick.
What is in the box.
Everything needed to have it working the day it arrives. No wiring, and no separate trip for a bulb.
- Lamp
- The glowing shade and its printed base, held by magnets so the shade lifts straight off. One size.
- Material
- The shade in translucent PLA; the base in matte PLA. Printed entirely in PLA, a plastic made from plant sugars - from crops such as corn - instead of oil.
- Light
- A rechargeable LED module in the base, charged over USB-C; the cable is in the box. Battery and running time will be given once the module is chosen.
- Colours
- Every part in its own colour, chosen on the page. Light colours pass more light; dark ones less.
- Made
- To order, in Malaysia. Ships by Tue 27 Oct.
If you are not sure
The same answers the product page gives, so nothing changes between here and checkout.
What it is made of
Translucent where the lamp glows, matte for the trim, printed one fine layer at a time. Printed entirely in PLA, a plastic made from plant sugars - from crops such as corn - instead of oil.
Each spool varies very slightly in tint, so two lamps bought months apart may not be an exact colour match. For lamps that must match, order them together.
Which bulb, and why it matters
LED only, 6 W or less, and this one is not a preference.
Never an incandescent or halogen bulb: inside a closed shade it runs far hotter than a printed lamp is made for. A 6 W LED runs far cooler, which is why only LEDs are allowed. Every lamp ships with its LED.
2700 K is the warm white these are rendered and finished against. Keep the lamp out of hot direct sun as well.